Dmp xr500n user manual

Occasionally, graphic touchscreen keypads may have displayed a white screen during processing which required the user to cycle power to the keypad. Avoid spraying cleaner directly onto the keypad, over-saturating cleaning cloths, or allowing cleaner to make contact with internal electronic components, cables, or power sources.

This enables installers to use a INT Series graphic keypad to program these devices locally. When a INT Series Wireless Touchscreen Keypad is powered on for the first time, the boot screen is displayed, then the home screen is displayed for approximately 15 seconds before transitioning automatically to the pairing screen.

When updating a CellCom or iCOM Series Communicator that was Version or lower and using Dealer Admin to program the unit, the communicator would send unnecessary information in communication programming.

Dealer Admin would display an error when trying to send programming to these communicators. If you have a CellCom or iCom that is Version or higher, this is not an issue. When a backup database is configured, SCS-VR writes panel check-in messages to the primary database and copies them to the backup database.

In previous software versions, SCS-VR attempted to copy check-in messages to the backup database even if it was down. This issue is resolved with this date code release. This feature has been added to support the upcoming version firmware of DMP Universal Communicators. Upon receipt of those messages, it will process only the CID portion of the message out to the Central Station Automation. To load the software onto the SD Card:.

Note: These two files need to be placed on the root directory of the SD card, not inside a folder. Previously, panel schedules could only be disabled. Now, you can fully delete a panel schedule. Turn on Allow deletion of items that normally may only be disabled , right-click the panel schedule, and select Delete. The same update applies to user code profiles. Turn on Allow deletion of items that normally may only be disabled , right-click the user code profile, and select Delete.

With some XR Series panels, data packets that exceeded the expected length would inadvertently be cut short. Due to this, some messages were rendered invalid. The more you can rely on a single administrative portal, the more efficiently you can fully manage your business. Dealer Admin continues to expand, giving you more administrative tools, organized in one convenient place.

For details about that version, the Technical Update is also posted there for review. When the exit delay time ex pires, all disarmed zones are armed. Page Key Fob Disarming A zone that is force armed is restored into the system if it later returns to normal.

A zone that is bypassed remains bypassed until the system is disarmed. See steps 7a through 7d. This lets users know that they are attempting to disarm outside of their authorized time. NO YES option displays. Arm Perimeter — Press 6 for 2 seconds. Arm All — Press 1 for 2 seconds. Arm Sleep — Press 7 for 2 seconds to arm the perimeter and interior areas and leave the bedroom area off.

Arm Away — Press 1 for 2 seconds. When the delay expires, the exit zones are armed. You may be prompted to enter your user code. Page User Menu 2. NO YES displays. Select YES. Page Alarm Silence Make sure all smoke is cleared from around the area of the smoke momentarily. The keypad returns to the Status List display.

Page Zone Status Refer back to step 3. After displaying the zone status, ZONE: - returns for you to 5. To Reset a zone, enter the zone number and select RST. Page Browser Feature The keypad also displays the name of each zone as its 8.

The zone number automatically disappears. You can then device is opened. The system then displays its firmware version, the panel mode, and then exits the User Menu.

Profile 99 is predefined in the system by sent to the receiver unless pre-programmed at installation the factory. In an XR Series system you can assign areas 1 to to be sent. In an XR Series panel you can assign areas 1 to 8. Page Adding User Profiles When you complete Selecting all User Profile menu 9. Page User Codes You may enter up to 32 characters for the name. As needed, system, default profiles for the Guest 1 house system, refer to Appendix C for Entering User Names information.

User Profile - The user is also assigned a Profile 1 to 99 by the person administrating the system. The profile number determines the areas and functions the user can access.

Page Browser Feature Select key and enter the new user code. The display then shows the current user name. Press any top row key to clear. Another new feature, Power Fail Delay, allows the user to delay Power Fail messages for up to 15 hours; 9 hours was the previous maximum Power Fail Delay time. These exciting new features may by "Flashed" free of charge to your new XR and XRN systems, without making a site trip, by simply downloading these updates into the latest version of Remote Link and updating the panel's software.

The Flashable software of the XR now saves you money on every installation. YES allows the panic zone test verification and failure results to be sent to the Central Station receiver. NO disables the panic test report. The default setting is NO.